Single DIN CD Player Install

JAY-929
Global Moderator
Global Moderator
Posts: 264
Joined: Tue Nov 03, 2009 10:22 pm
Make: Mazda
Model: 929
Year: 1988
Body Code: HC01
Location: Melbourne, Victoria, AU

Single DIN CD Player Install

Post by JAY-929 » Thu Mar 11, 2010 2:52 pm

Image

Here's the standard head unit. I have to laugh at the 929 sales brochure's description of the stereo:
THE SOUND OF THE FUTURE

Another enjoyable feature on this new Mazda V6i is the superb 6 speaker audio system. This system contains stereo AM/FM radio, electronic tuner, hig power amplifier, graphic equaliser and cassette deck.

All of these components are especially blended to offer the ultimate in listening and driving pleasure....
... yeah... about that... :lol: hahahaha

Let's rip it out :)

Image

You'll need to remove the panel under the glovebox first so you can access the first of 2 10mm nuts to remove.

Image

Image

After taking these 2 nuts off, the unit should just slide out. Surround and all.

Image

Image

Now, one by one, starting pulling out all these plugs (takes a while.. there's enough there to keep a grown man busy! hahaha)

Image

Once all that is done, you should see the pretty picture below:

Image

OK, Don't lose the mounting bracket... you need that. So, unscrew all the "superb" components with a philips head screwdriver (or cordless tip).

Image

Image

You'll notice it practical falls apart once you unscrew it all. Now, you have your bracket, let's get down to business...
1988 MAZDA 929 HC SERIES 1 HARDTOP
CURRENTLY UNDER CONSTRUCTION
JAY-929
Global Moderator
Global Moderator
Posts: 264
Joined: Tue Nov 03, 2009 10:22 pm
Make: Mazda
Model: 929
Year: 1988
Body Code: HC01
Location: Melbourne, Victoria, AU

Re: Single DIN CD Player Install

Post by JAY-929 » Thu Mar 11, 2010 3:02 pm

The unit I'm installing in MY 929 is the ALpine CDA-7998R. It's a 1.5 Din unit (which is the face size only, as the unit is still housed in a single din casing), so I'll need to take the clearance of the fold-out face into consideration. I'll need to modify my existing bracket, in order to get the head unit face sitting flush up front. I'm going to drill holes where I can fix the unit to the bracket.

Image

Acquire the drill tip you need for the application (in my case, it's a 6mm tip) and drill to suit the screws you're intending on using to fix the unit to the bracket.

Image

Image

PLEASE NOTE: ALWAYS WEAR SAFETY GLASSES WHEN DRILLING INTO METAL!!

Image

You should have the above picture once you're done. Now line the holes up to the unit, to make sure you're on the right track.

Image

Once you're done, screw the unit to the mounting bracket for a "trial fit".

Image

Image

Now, I'm satisfied with how that sits. So, it's time to get the wiring organised :)
1988 MAZDA 929 HC SERIES 1 HARDTOP
CURRENTLY UNDER CONSTRUCTION
JAY-929
Global Moderator
Global Moderator
Posts: 264
Joined: Tue Nov 03, 2009 10:22 pm
Make: Mazda
Model: 929
Year: 1988
Body Code: HC01
Location: Melbourne, Victoria, AU

Re: Single DIN CD Player Install

Post by JAY-929 » Thu Mar 11, 2010 3:24 pm

Now, to make life easier for you, I've attached a link to a wiring chart for the HC 929 HERE.
However, I'm a firm believer of finding things out for myself. So, I took out a test light and got busy.

I would USUALLY connect my test light to the battery's negative terminal, so I can find my constant and accesories wires. Once I've discovered these, I can find out my other wires. However, I discovered the illumination wire, which is actually a negative wire with everything switched off. However, in most cases, this wire will have 12v+ on it when the lights are on. So, don't go connecting your ground wire to it (as some do). I'll show you where I mounted my ground wire. For now, you'll see me locating the power/accessory wires below:

Image

Image

Too easy! I can start stripping these wires and getting ready to solder.

I use the following wire strippers from Jaycar @ $29.95:

Image

Make sure your power loom is NOT connected when you do this.
Now I grab my wire and strip it back and twist them together, as pictured below:

Image

I was slack once again, as USUALLY (and ideally), after you've stripped your wires back, cut off a small bit of "heatshrink" and place it on the wire you plan on soldering together. Then once you've soldered them, get a heat gun (or a cigarette lighter will do it) and heat the heat shrink onto the soldered area. But on this occasion, I was in a rush, so I used sparky's tape.

You're ready to solder. Because I'm not Goro from Mortal Komabt, I don't have another pair of arms to take pictures WHILE I'm soldering, so forgive me. However, your soldered join should look like this:

Image

Now, do the same for the remaining wires:

Image

Once you're done, all your wires should look like this:

Image

The extra wires done are the Illumination and Antennae Trigger wires. Refer to the link at the top of this post to locate them and solder them with the according wires from your head unit.

Now.... Ground wire mounting....
Last edited by JAY-929 on Thu Mar 11, 2010 3:52 pm, edited 1 time in total.
1988 MAZDA 929 HC SERIES 1 HARDTOP
CURRENTLY UNDER CONSTRUCTION
JAY-929
Global Moderator
Global Moderator
Posts: 264
Joined: Tue Nov 03, 2009 10:22 pm
Make: Mazda
Model: 929
Year: 1988
Body Code: HC01
Location: Melbourne, Victoria, AU

Re: Single DIN CD Player Install

Post by JAY-929 » Thu Mar 11, 2010 3:40 pm

Fix a open ring terminal to the end of your ground wire and this will make life ALOT easier with regards to mounting the wire.

Image

Solder the wire and taped it (or heatshrink it) and I mounted it at the back of the radio mounting bracket. I put metal spacers in between the bolt head and the bracket, and the ring terminal and the bracket; finally fixing it with a nut to suit the bolt. You should have the following picture below:

Image

Image

Now... you should have power! To check, connect your power loom to the unit and flick on the ignition to accessories and hit the power button your your head unit. IF done correctly, you too can be happy to see this:

Image

WOO HOO!!! Now, If you running an amplifier, you will attach your RCA leads (and stacker cable if you're running one also) to the appropriate pre-outs on your head unit and then feed them through to the back of the console. Once you're done that, DOUBLE check that all wires are connected (and none are exposed) and slot the mounting bracket back into place. Screw up the 10mm nuts at the back, and you should have this to look at now:

Image

Image
1988 MAZDA 929 HC SERIES 1 HARDTOP
CURRENTLY UNDER CONSTRUCTION
JAY-929
Global Moderator
Global Moderator
Posts: 264
Joined: Tue Nov 03, 2009 10:22 pm
Make: Mazda
Model: 929
Year: 1988
Body Code: HC01
Location: Melbourne, Victoria, AU

Re: Single DIN CD Player Install

Post by JAY-929 » Thu Mar 11, 2010 3:49 pm

If you want a pocket to fit underneath, rush into Autobarn and ask them for either of the following items:

FP987599

Image

FP9015

Image

FP9008G

Image


If you want to get a whole new install kit for your Mazda.. ask for the following:

FP997501

Image

If you need wiring harnesses, Crutchfield in the States have harnesses.

Here for select Ford, Kia, Mazda, and Mercury models, 1983-up

Here for select Ford and Mazda models, 1989-up

Any questions.. please post up and I'll be happy to help :)
1988 MAZDA 929 HC SERIES 1 HARDTOP
CURRENTLY UNDER CONSTRUCTION
chevyboy6902
Registered users
Registered users
Posts: 12
Joined: Mon Nov 02, 2009 3:29 am
Make: mazda
Model: 929 S
Year: 1991
Body Code: HC
Location: michigan

Single DIN CD Player Install

Post by chevyboy6902 » Fri Mar 12, 2010 1:26 am

Hey thanks for the detailed radio removal and install it has been a big help
:D
JAY-929
Global Moderator
Global Moderator
Posts: 264
Joined: Tue Nov 03, 2009 10:22 pm
Make: Mazda
Model: 929
Year: 1988
Body Code: HC01
Location: Melbourne, Victoria, AU

Re: Single DIN CD Player Install

Post by JAY-929 » Fri Mar 12, 2010 1:40 am

You are most welcome, my friend :)
1988 MAZDA 929 HC SERIES 1 HARDTOP
CURRENTLY UNDER CONSTRUCTION
Matsuda9
Site Admin
Site Admin
Posts: 612
Joined: Thu Jun 18, 2009 11:09 am
Make: Mazda
Model: Luce
Year: 1988
Body Code: HCFS
Location: Melbourne, AU
Contact:

Single DIN CD Player Install

Post by Matsuda9 » Fri Mar 12, 2010 10:08 am

good write up Jay 8-)

although i still dislike your ignorance towards heatshrinking :D
Image
JAY-929
Global Moderator
Global Moderator
Posts: 264
Joined: Tue Nov 03, 2009 10:22 pm
Make: Mazda
Model: 929
Year: 1988
Body Code: HC01
Location: Melbourne, Victoria, AU

Re: Single DIN CD Player Install

Post by JAY-929 » Fri Mar 12, 2010 10:18 am

HAHAHAHAHA!

I was waiting for that one! Next build up, I will :P You have my word.

And thanks :)
1988 MAZDA 929 HC SERIES 1 HARDTOP
CURRENTLY UNDER CONSTRUCTION
wasname
Registered users
Registered users
Posts: 1
Joined: Tue May 15, 2012 8:12 am
Make: Mazda
Model: 929
Year: 1988

Re: Single DIN CD Player Install

Post by wasname » Mon May 21, 2012 8:53 am

I assume you've upgraded the battery to run your amps?
Can I ask what make/model you'd recommend as I think my sub is bleeding my battery dry.
Cheers.
Post Reply